Electrolux & Zanussi Glass washer Parameter Code

CONVOTHERM mkn RATIONAL ANGELOPO ELECTROLUX SUZUMO COOKTEK AMANA AUTOFRY FRYMASTER

dishwasher troubleshooting|glass washer service manual|dishwasher error code|service errors

hood type dishwasher|electrical wiring diagram|parameter.

Maintaining commercial kitchen equipment helps keep your kitchen best to be familiar with

the restaurant and Hotel equipment by reviewing the owner's manual to Contact a professional

repair technician to conduct regular planned

Rational Oven Cooking Programme 📹 Rational SCC Function Test 📹Rational Parts

Vario Rational How to Remove The Parts📹 Vario How to Updates Softwere

Rational Combi Master Plus Cooking 📹 Rational Oven How to Connected Network

Rational|MKN|Convorthem|CookTek|Eloma|Alto shaam|Electrolux|Inoxtrend|Fagor.

Note : Subscribe E-Mail and YouTube to get more information,we are ready to help you our best

don't hesitate to contact us.

Electrolux and Zanussi Dishwasher \| Electrolux and Zanussi Glasswasher

KEYBOARDS HOODTYPE Style UNDERCOUNTER Style

SETTING MODES: To enter into one setting mode the appliance should be in stand-by: switch on the appliance, no cycles selected. Is useful keep door open to avoid start cycle in case of not simultaneously pressure of the two keys.

Enter into General Parameters Enter into Factory Parameters (Hold down buttons for at least five seconds). (Hold down buttons for at least five seconds)


SETTING MODES: To enter into one setting mode the appliance should be in stand-by: switch on the appliance, no cycles selected. Is useful keep door open to avoid start cycle in case of not simultaneously pressure of the two keys.

Zanussi Dishwasher\|Electrolux Dishwasher A Alarms that stop the dishwasher Remedy A1 Error Want of water Is the water open?\| Does the water load solenoid valve work? Is the water feed flow a min. of 5 l/min? Is the water inlet filter clean? Is the load solenoid valve filter clean? Is the overflow inserted? Is the main board (ATM-PRES) CN2 connector correctly positioned? Do the tank/boiler pressure switches work properly?

C8 Error During rinse phase boiler doesn't empty Are the rinse arms clogged? Does the rinse pump work correctly? Is there water in the level sensor tube? Is there scale in the boiler? Does the boiler level sensor work properly? C9 Error Automatic hood out of order See par. C1 - Alarm codes for automatic hood type dishwashers When the alarm C9 appears, to facilitate fault-finding another parameter providing a more detailed indication has been introduced.
B1 Error Drain not efficient Has the overflow been removed? Is the water drain blocked? Is the drain pump blocked? Are the air trap and tank pressure switch clean? Is there a constriction in the drain tube? Is the pump breather pipe returning to the tank clogged or constricted? Does the tank pressure switch work properly? Is there a hole in the drain tube (only for versions with drain pump)? B2 Error Overflow alarm Is the water drain blocked? Are the air trap and tank pressure switch clean? Does the tank pressure switch work properly? Is the load solenoid valve blocked? (E1 - LOAD_EV) Is the load solenoid valve relay stuck? (RL8 - LOAD_EV) C1 Error Boiler temperature rise too fast Does the boiler level sensor work properly? The boiler could be empty Are non-original power resistances installed? C2 Error Boiler temperature too high Has the boiler temperature been changed (btC - increased above 90°C)? Has the software alarm value been modified (bHi)? Does the boiler level sensor work properly? Is the boiler relay stuck (see RL2, RL3, RL4)? C3 Error Tank temperature too high Is the feed water above 60°C? Has the software alarm value been modified (bHi)? Is the rinse water temperature too high? Is the tank relay stuck (RL5 - TUB_HEAT)? C4 Error Tank temperature sensor out of order Is the temperature sensor broken or disconnected (NT1)? Is the temperature sensor connector correctly inserted? C6 Error Boiler temperature sensor out of order C7 Error Boiler temperature sensor out of order C10 Error Rinse temperature sensor out of order C11 Error

E1 Error Communication error Is the connection between main board and control panel correct? Are the connectors correctly connected? Are connector contacts clean? E2 Error Tank temperature low Does the tank heating element work properly? Are the connectors correctly connected? Are the dishwasher feed voltage and current correct? Is the relay RL5 on the board disconnected or faulty? E3 Error Boiler temperature low Does/do the boiler heating element/s work properly? Are the connectors correctly connected? Does the possible remote control switch connected to the heating element work correctly? Is there power at the remote control switch input terminals? Does relay RL2 on the board work properly?
F21 Error Water softener operation errors This alarm appears in case of malfunctioning in the continuous water softener. To reset errorF21 it is necessary to disconnect and reconnect the main power supply to the machine by means of the main switch on the external power board. F22 Error Communication errors between the mother board and softener board This alarm appears in case of problems in communication between the mother board and water softener board; check the connection between mother board connector J1 and water softener connector ST8.


DISHWASHER WITH INCORPORATED CONTINUOUS WATER SOFTENER Dishwashers with incorporated continuous water softener have a continuous softener in the water circuit. By means of special resins, this device removes the calcareous substances from the feed water, supplying decalcified water for washing. To activate the continuous water softener, set the parameter SER (in the HCP family) to the value 9 or the value 11 if the water softener board is connected to the LK485 board. For the continuous softener to work properly the resins must be regenerated periodically with a frequency depending on the hardness of the inlet water, the number of wash cycles carried out and the max. hardness set with the parameter SrU (in the CFG family)Unlike conventional water softeners, this continuous softener does not require machine stops for regenerating the resins. To regenerate the resins it is necessary to put coarse salt in the special container located in the dishwasher. In particular, the salt container must be filled when the dishwasher is used for the first time and whenever the messages SAL 0 or SAL END are displayed at the start or end of a wash cycle. The salt container holds up to 1.5 kg of salt.