rational icombi spare parts|amana parts|mkn parts|convotherm parts|menumaster
winterhalter parts|inoxtrend manual|cooktek parts|zanussi parts
Note : Subscribe E-Mail and YouTube to get more information,we are ready to help you our best
don't hesitate to contact us.
| How to Diagnosing Units SSC WE Service Level |
| Maintaining commercial kitchen equipment helps keep your kitchen and best to be familiar with the restaurant and Hotel equipment by reviewing the owner's manual to Contact a professional repair technician to conduct regular planned.The Rational Self Cooking Center not only makes cooking easy, but it also has some helpful features for technicians who service the equipment. Perhaps one of the best features is the machine’s ability to offer diagnostic codes. Each code will tell you what’s wrong with the oven, allowing you to tackle the issue quicker. |
| What’s was faulty appearing? Unit runs in emergency humidity control |
| Remedy?? Humidity control is out of function and needs to be repaired or replaced |
| Service 31 |
| What’s was faulty appearing? Faulty core probe |
| Probes (x): |
| 31.1: Shaft probe |
| 31.2: Fifth probe (near shaft) |
| 31.4: Fourth probe |
| 31.8: Third probe |
| 31.16: Second probe |
| 31.32: First probe in tip |
| COMBINATION OF FAULTY PROBES CAN DISPLAY (EXAMPLE: FAULTY FOURTH AND THIRD PROBE WILL DISPLAY AS “31.12″) |
| Remedy? Repair or replace the faulty probe |
| Service 32 1-2 |
| What’s was faulty appearing? Faulty ignition box |
| Ignition boxes: |
| 32.0: Ignition box top |
| 32.1: Ignition box bottom (floor models only) |
| 32.2: Both ignition boxes |
| Remedy? Change the ignition box that appears in error code |
| Service 33 1-2 |
| What’s was faulty appearing? Faulty ignition box |
| Ignition boxes: |
| 31.1: Ignition box bottom (floor models only) |
| 31.2: Both ignition boxes |
| Remedy? Check the ignition wiring or ignition box gas valve and supply |
| Service 34 |
| What’s was faulty appearing? Bus signal problems |
| Probes (x): |
| 34.1: Motor top |
| 34.2: Motor bottom |
| 34.4: Ignition module top |
| 34.8: Ignition module bottom |
| COMBINATION OF BUS SIGNAL PROBLEMS CAN DISPLAY (EXAMPLE: IGNITION MODULE TOP AND BOTTOM WILL DISPLAY AS “34.12″) |
| Remedy? See if the bus cable plug and cable connection are connected or damaged |
| Service 35 |
| What’s was faulty appearing? Bus signal can’t be processed due to disconnected ultravent |
| Remedy?? Connect the ultravent |
| Service 36 |
| What’s was faulty appearing?Defective differential pressure sensor P1 |
| Remedy?? Repair or replace the sensor |
| Service 37 |
| What’s was faulty appearing? Differential pressure sensor P1 isn’t in expected range |
| Remedy?? Check the connection of hoses |
| Service 40 |
| What’s the cause? Care pump is broken or doesn’t fill enough solution into the steam generator |
| Remedy?? Check if the hose from the care pump outlet isn’t kinked and reset error by completed a successful rinse program |
| Service 41 |
| What’s was faulty appearing? Defective solenoid valve Y3, blocked moistening valve or CDS isn’t sending pulses |
| Remedy?? Resolve issue and reset error by completed a successful rinse program |
| Service 42 |
| What’s was faulty appearing? Defective solenoid Y4 Care, hose to Care container blocked/kinked or CDS isn’t sending pulses |
| Remedy?? Resolve issue and reset error by completed a successful rinse program |
| Service 43 |
| What’s was faulty appearing?Solenoid Y1, Y3 or Y4 is passing water/won’t close and CDS is always sending pulses |
| Remedy?? Reset error by completed an abort program |
| Service 44 |
| What’s was faulty appearing? Steam not heating during CleanJet+Care |
| Remedy?? Reset error by completed an abort program |
| Service 60 |
| What’s was faulty appearing? Incorrect initialization of ignition box? |
| Remedy?? Check the gas settings and switch the unit off and on again before running SD Repair program? |
| Service 63 |
| What’s was faulty appearing? Self-test running without water |
| Remedy?? Allow the unit to cool down and see if? B1, B2 and B4 are below 104?F (40?C); Set Selftest to ON and switch unit off and on |
| again before running Selftest |
| Service 100 |
| What’s was faulty appearing? Defective SC pump or calcified level electrode |
| Remedy? Reset error by completed an abort program |
| Service 120 |
| What’s was faulty appearing? Defective Care pump M12 or level electrode |
| Remedy? Reset error by completed an abort program |
| Machine Spare Parts Manual's |
| Rational Parts / MKN Parts / Conveothem Parts / Inoxtrend parts / Fagoor Parts / True Parts |
| Rational Vario Cooking Parts / Meiko Dishwasher Parts / Alto Shaam Parts |
| Vario Cooking Rational Software Update's / Amana Parts / Menumaster Parts / Merrychef Parts |
| Ice O Matic Parts / Blender Robot Coupe Parts / Comenda Parts / Blender Waring Parts |
| Ice Machine Scotsman parts / Hozhizaki Ice Machine Parts / Hobart Dishwasher Parts |
| Machine Error Code's |
| Rational Error Code's 〰 MKN Error Code's 〰 Conveothem Error Code's 〰 Rational User Manual |
| Vario Cooking 〰 Equipment's Brand's 〰 Meiko Dishwasher Features 〰 Rational Networking |
| Vario Cooking Rational Software Update's 〰 Amana Microwave Latest Features |
| Ice O Matic 〰 Leading Microwave Equipment's 〰 Rational Factory 〰 Glass Washer |
| Ice Machine Scotsman parts 〰 Hozhizaki Ice Machine Parts 〰 Hobart Dishwasher Parts |
| Rational Oven Cooking Programme 〰 Rational SCC Function Test 〰 Rational Download Document |
0 Comments
how can i help you. if you have any problem let me know