💧ELOMA OVEN ERROR CODE AND SERVICE MANUAL

Eloma Oven Error Code, Troubleshooting , Wiring Diagram , How to Diagnose Machine ,  

Software Updates , Eloma oven Spares Parts , Service Code, How to do the Programming

CONVOTHERM mkn RATIONAL ANGELOPO ELECTROLUX SUZUMO COOKTEK AMANA AUTOFRY  FRYMASTER

Error      code	Description		Possible   cause / solution
111	Probe chamber      1 (top)      No signal		Check   probe 0,789mV at 20°C, replace defective probe.      Shorten the terminals 11 & 12. Reset, if error still there replace the   PCB Oven will NOT   operate with a defective probe.
112	Probe chamber      2 (bottom) No signal		Check probe 0,789mV at 20°C, replace defective      probe.      Shorten the terminals 13 & 14. Reset, if error still there replace the   PCB Oven will NOT operate with a defective probe.
113	Meat probe      No signal sensor 1		Check probe 0,789mV at 20°C, replace defective      probe.      Shorten the terminals 1 & 2. If error still there replace the PCB      Meat probe operation is possible
114	Meat probe      No signal sensor 2		Check probe 0,789mV at 20°C, replace defective      probe.       Shorten the terminals 1 & 4. If error still there replace the PCB      Meat probe operation is possible
115	Meat probe      No signal sensor 3		Check probe 0,789mV at 20°C, replace defective      probe.      Shorten the terminals 1 & 6. If error still there replace the PCB      Meat probe operation is possible
116	Meat probe      No signal sensor 4		Check probe 0,789mV at 20°C, replace defective      probe.      Shorten the terminals 1 & 8. If error still there replace the PCB Meat probe operation is possible
113 114      115 116	Meat probe      No signal off all      4 sensors		The common wire is defective, change the probe.      Meat probe operation is NOT possible
117	Probe waste water (drain)      No signal		Check probe 0,789mV at 20°C, replace defective probe.      Shorten the terminals 15 & 16. If error still there replace the PCB      Oven will operate with a defective probe.
127	Probe waste      water (drain)      {Genius/Genius-T      only}		Follows error 117: Value for temperature is not correct.      Oven will operate with a defective probe.

Error      code		Description			Possible   cause / solution
211		Upper safety      thermal release			Reset the upper safety thermal release.       Check the fuse F1 (8 Amps slow) on PCB.       If the STR has not released, check if the motor temperature sensor switched of, this is a bi-metal trip, which resets itself when cooled down. If so, control the main/motor fuses. Replace     and check possible causes: Defective motor windings or the motor is blocked.       Is the contact 13/14 of main contactor K1/Q1 closed?      Or check X10, pin 1/2. This is a security loop; if this loop is open the contactor goes off after a few      seconds.       If this error occurs a couple of times it is likely that a motor contactor or the main-contactor has a bad contact, in this case replace the contactor.       Oven cannot operate!
212		Lower safety      thermal release			Reset the lower safety thermal release.       Check the fuse F1 (8 Amps slow) on PCB.       If the STR has not released, check if the motor temperature sensor switched of, this is a bi-metal trip, which reset itself when cooled down. If so, control if the main/motor fuses. Replace and check possible causes: Defective motor windings or the motor is blocked.       Is the contact 13 / 14 of main contactor K2/Q2 closed?      Or check X10, pin 3/4.This is a security loop; if this loop is open the contactor goes off after a few seconds.       Oven cannot operate!
1		Door   open			Close the door / operating panel.       Check the door switch, inside the operating panel. You may check this by shorting the terminal 9 & 10 at X10.       Is the magnet lost (Inside the door frame)?
2		Emergency      opening door			Door was opened with the emergency opening.       Check closure mechanism.       Oven can’t operate!
3		Door   switch			Micro switch of door from motor not activated.       Micro switch is loose.       Oven can’t operate!
4		Door   not closed			Door hook defective.       Magnet switch faulty.       Oven can’t operate!
5		Door motor      works permanently			Door can’t get closed.       Oven can’t operate!
6		Door not in position			.No defined position.       Oven can’t operate!
311		No water / low      water pressure			Open the water tap.       The water flow pressure must be checked, 2 bar / 29       SI for soft water.       Check the water pressure switch, terminal 11 & 12.       Autoclean will pause until pressure is high enough.
312		Not enough water			Is the appliance connected to water?       Check if water tap is open.       Control the flow water pressure       Adjust the solenoid valve to the correct amount of      water. See table “Table 1.2.2”.       Refer 2.3.1 No steam!
313		Hand   shower			Hand shower is not working; only Joker models!
314		Fill   level tank			Water tank is empty.       Only EB30
315		Water flow w/o request			Water flows into the cavity but not required by program/user.       Only EB 30 B/T and XL       Oven cannot operate!
711		No flame upper      chamber			Is the phase at L1, polarity!       Is the kitchen ventilation system working? Interlock?       Check the ionisation current of the gas firing (Part A4 pin J5, older version X3)      Reset: Pressing restart.   Refer 2.6.2 Restart Gas
712		No flame lower chamber			Is the phase at L1, polarity!       Is the kitchen ventilation system working? Interlock?       Check the ionisation current of the gas firing (Part A4 pin J5, older version X3)      Reset: Pressing restart.

Error      code		Description								Possible   cause / solution
213		No motor signal Only Genius, Genius-T, MB- Gas, EB50/80T models!								Check the main / motor fuses. Replace them, if blown and check possible causes: Defective motor windings or the motor is blocked.       Check motor parameters for start up and slow down.      See programming manual.       Check the hall generator.       Units with frequency converter may block operation when switched Off/On instantly. Please wait 5 seconds after switch off before switch on again.       Oven cannot operate!
Error      code		Description								Possible   cause / solution
511		Pre-warning: PCB temperature      65°C								Clean air filter, located at the bottom of the front panel.       Check if the compartment fan and the fan in the front panel are working. See chapter 2.2.4       Oven can operate!
512		Warning: PCB      temperature      70°C								Clean air filter, located at the bottom of the front panel.       Check if the compartment fan and the fan in the front panel are working. See chapter 2.2.4       Oven switches off!
0      513		Warning: PCB      temperature      68°C								Slow overheated PCB.       The installation prevents ambient air flow for a cooling effect.
AC		Breaking off      Autoclean								Press start, the oven will operate the flushing mode. Message comes up after breaking off the Autoclean cycle or      interrupting the power supply.

Appliance															Water   amount steam																																														Water   amount drainage
Joker B, T, (Old C)															6 l/h (0.1 l/min)      1.32 Imp. Gal.																																														30 l/h (0.5 l/min)      6.60 Imp. gal.
MA, MB, GT      6-11															16 l/h (0.26 l/min)      3.52 Imp. Gal.																																														55 l/h (1.09 l/min)      14.30 Imp. Gal.
MA, MB, GT      10-11															19 l/h (0.32 l/min)      4.18 Imp. Gal.																																														55 l/h (1.09 l/min)      14.30 Imp. Gal.
MA, MB, GT      12-21															25 l/h (0.42 l/min)      5.28 Imp. Gal.																																														55 l/h (1.09 l/min)      14.30 Imp. Gal.
MA, MB, GT      20-11 Per chamber!															19 l/h (0.32 l/min)      4.18 Imp. Gal.																																														55 l/h (1.09 l/min)      14.30 Imp. Gal.
MA, MB, Genius-T      20-21 Per chamber!															25 l/h (0.42 l/min)      5.28 Imp. Gal.																																														55 l/h (1.09 l/min)      14.30 Imp. Gal.
EB-B/T 50															25 l/h (0.42 l/min)      5.5 Imp. Gal.																																														---
EB-B/T 80															30 l/h (0.5 l/min)      6.6 Imp. Gal.																																														---
EB-B/T 30															15 l/h (0.25 l/min)      3.52 Imp. Gal.																																														---
EB-B/T 30 XL															18 l/h (0.3 l/h)      3.96 Imp. Gal.																																														---
EB-B/T 30 (XL) Tank															Solenoid open!																																														---